Weifang Tianshili Plastic Co., LTD

+8615615660036

Company news Current location: Home>>News>>Company news

Contact us

    Contacts:Victor
    Mobile phone:+8615615660036
    Website:www.cntianshili.com
    Address:South head of East Outer Ring Road, Zhucheng City, Weifang City, Shandong Province
How to clean the plastic drain board? The manufacturing process of the plastic drain board
Author:Weifang Tianshili Plastics Co., Ltd  Time:2021-01-22 Number of hits:872

In articles such as chicken house plastic fecal leakage floor, poultry lighting, etc., we learned some unknown knowledge, but "how to clean the plastic fecal leakage board and the manufacturing process of the plastic fecal leakage board" is still relatively unfamiliar to many people. Today, let's understand:

We should make good preparation before cleaning the floor with feces leakage, that is, to remove the solid feces, stale wood and inflammable electrical appliances from the pigsty, and remove the equipment that hinders the re washing, then we can wash it with low-pressure water.


When washing the floor with fecal leakage, the top-down method can be adopted, and the wide-angle nozzle can be used to wash the floor in a large area, and any part that has indirect war with the pig body should be completely cleaned and disinfected. Then there is the cleaning of the concrete and the aisle.


Specifically, we should pay attention to the cleaning of the floor with fecal leakage, and clean it from the outside. On weekdays, the sewers and sewers should be passable and free of accumulated water. The sewers should also use a low-pressure water gun to wash the plastic. How to clean the plastic fecal leakage board? Only by insisting on the passage at any time can we avoid bacterial reproduction.

You may prefer this article:

Method 1:

Mixing two kinds of concrete "fine material, coarse material" two times mold making effect is better: fine material is also called bottom material "ratio" (cement 42.5R), cement 1, sand 2, brightener, the dosage is 4-5% of the cement, add water properly. Mix it for 15-20 minutes until it is sticky, set the mold for about 5 seconds, the thickness of the bottom material is about 5-8 mm, and then place it for 10-20 minutes, and then put in the prefabricated steel bar with a diameter of 2-4 mm, one for each blank. The depth of steel bar is 3-3.5mm. When loading coarse materials, the "ratio" of coarse materials is about cement 1 sand 2 gravel 2-2.5, not too thin. 5-10 seconds, put into the indoor cover with plastic cloth to maintain 2-3 days of the manufacturing process of the plastic drain board, 2-3 days later to the outdoor after 9 am demoulding is the most appropriate.

Method 2:

Mixing a kind of concrete for twice mold making can also be: the ratio (cement 42.5R) cement 1 sand 2 gravel 2-2.5. Brightener, 3-4% of cement content. Do not mix too thinly for 5-10 minutes. The thickness of the concrete material is about 5-8 mm for 5 seconds. Then put in the prefabricated steel bar with a diameter of 2-4 mm, or one steel wire for each blank. The depth of steel bar is 3-3.5mm.. It is most appropriate to mold the concrete for 5-10 seconds, maintain the plastic cloth on the indoor cover for 2-3 days, and demould the mold at 9 a.m. after 2-3 days.

The content of "how to clean the plastic fecal leakage board? The manufacturing process of the plastic fecal leakage board" is carefully prepared for you by our editor. Do you remember what was said in the last part of the plastic fecal leakage floor of the chicken house? These may not be comprehensive, we will explain them one by one in the future!





Home About us News Product Case Video Contact us

Product

Animal husbandry series
Consolidation series
Tray series

Mobile QR code

Contact us

Weifang Tianshili Plastics Co., Ltd

——

Contacts:Victor
Mobile phone:+8615615660036
Email:zctslmj@163.com
Website:www.cntianshili.com
Address:South head of East Outer Ring Road, Zhucheng City, Weifang City, Shandong Province